Dosimetry study of three-dimensional print template for 125I implantation therapy

Background 125I seed implantation has been found to show good therapeutic effects on tumors. Recent studies showed that three-dimensional (3D) print template-assisted 125I seed implantation can optimize radiation dose distribution. This study aimed to compare the dose distribution differences in 125I seed implantation among 3D print noncoplanar template- (3DPNCT), 3D print coplanar template- (3DPCT) assisted implantation and traditional free-hand implantation. Methods We systematically searched the PubMed, EMbase, Cochrane Library, Wan Fang Med Online, China National Knowledge Infrastructure (CNKI) from the earliest to November 2020 without time or language restrictions. And the references of primary literature were also searched. The outcome measures were dosimetry and operation time. This meta-analysis was carried out using Stata 12.0. Results A total of 16 original articles were selected for inclusion. The differences of D90, D100, V90, and V100 values pre- and post-implantation with traditional free-hand implantation showed statistically significant (p < 0.05). The differences of D90, D100, V100, V150, V200, and D2cc of organs at risk (OAR) values pre- and post-implantation with 3D print template showed no statistically significant (p > 0.05). Compared with traditional free-hand implantation without any templates, 3D print template could improve postoperative D90 (Standard mean difference, SMD = 0.67, 95% confidence interval (CI) = 0.35 to 0.98, p < 0.001), D100 (SMD = 0.82, 95%CI = 0.40 to 1.23, p < 0.001), V90 (SMD = 1.48, 95%CI = 0.95 to 2.00, p < 0.001), V100 (SMD = 1.41, 95%CI = 0.96 to 1.86, p < 0.001), and reduce operation time (SMD = − 0.93, 95%CI = − 1.34 to − 0.51, p < 0.001). In three studies, both 3DPNCT and 3DPCT plans were designed for all patients. The prescribed dose and seed activity were same. Pooled analysis of D90, D100, V100, D2cc of OAR, number of seeds and number of needles showed no significant differences between 3DPNCT and 3DPCT groups (p > 0.05). However, in 3DPNCT group, V150 and V200 were increased (SMD = 0.35, 0.49; 95%CI = 0.04 to 0.67, 0.02 to 0.96; p = 0.028, 0.043); the number of through bone needles was reduced (SMD = − 1.03, 95%CI = − 1.43 to − 0.64, p < 0.001). Conclusions Compared with traditional free-hand implantation, 3D print template-assisted 125I seeds implantation can optimize dose distribution and reduce the implantation time at the same time. Compared with 3D print coplanar template, 3D print noncoplanar template can increase the volume of high dose within tumor target and is more safer in the respect of puncture route. Supplementary Information The online version contains supplementary material available at 10.1186/s13014-021-01845-y.

surgery, delivering a high local radiation dose to tumor targets and sharply dropping off at adjacent normal tissues. Nevertheless, up to date, there was still no standard procedures for 125I seed implantation for other tumors in the body except prostate cancer. It was challenging to effectively preplan for seed implantation resulted from patients' body movement, organ movement, and bone structure interference. RIS implantation just relied on individual clinical experience and puncture techniques. Seed location and dose distribution were not the same as the preplan, which could lead to complications of operation and local recurrence of tumor.
In term of high-dose-rate (HDR) brachytherapy, Martinez developed an afterloading applicator that consisted of an template with a predrilled holes which were used as guides for trocars in 1984. And so, trocars could be inserted through the holes and produced optimal dose coverage of the tumor volume, which could reduce the degree of technical difficulty and improve the dose-rate distributions [3]. Aristei designed an 3D template which was confirmed to be a quick, easy, reliable and timesaving method to localize the volume of tumor target for HDR brachytherapy in breast cancer patients [4]. Mahantshetty included 113 patients with gynecologic cancers treated with template-based HDR interstitial brachytherapy boost, which resulted in a satisfactory clinical outcomes without any severe toxicities [5]. Coincidentally, doctors in China tried to implant RIS with the template which was designed individually by 3D printer. The use of 3D print templates including 3D print noncoplanar template (3DPNCT) and 3D print coplanar template (3DPCT) made it more precise to implant RIS, with a highly consistent dose distribution of target volume. Many studies showed that 3D print template-assisted RIS implantation could not only reduce the dosimetric differences between pre-and post-plan but also lower the difficulty of puncture [6][7][8]. However, the number of samples included in the past studies was small, and the quality was uneven. So, we aimed to peform a systematic review and meta-analysis of related researches on the dosimetry after RIS implantation with or without template.

Study selection
The meta-analysis was carried out according to the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) statement for reporting reviews and meta-analysis [9].
Major electronic literature databases were systematically searched, which included EMbase, PubMed, Cochrane Library, Wan Fang Med Online, CNKI. The search used various combination of subject words and free words, which included brachytherapy, iodine radioisotopes, iodine-125, 3-dimensional printing, 3D print. And the search strategy was determined after multiple presearches. Articles published before November 2020 were found in the search without publication and any language restriction. In addition, The researchers review the full texts of the included literature and carefully checked the list of references of the selected literature so as to avoid missing any other relevant researches on this topic.

Inclusion criteria
In order to be included in this meta-analysis, the study had to meet all the criteria as follows: (1) randomized controlled trials (RCTs) or non-RCTs or retrospective study; (2) 2-arm studies in which patients received 3D print template-assisted RIS implantation in the treatment group and traditional free-hand implantation in the control group or a single-arm study reporting OAR with 3D print template-assisted RIS implantation; (3) Studies had outcomes of dosimetry or operation time.

Exclusion criteria
The exclusion criteria include the following: (1) abstract, letter, case report, editorial, animal experiments, review, and other irrelevant studies; (2) no outcome measures.

Data extraction
Two researchers (E.C. and Y.Z.) searched and reviewed related studies and carried out the data extraction independently. When there was any controversy, articles would be sent to a third reviewer (H.Z) for assessment until they achieved a agreement. We extract information for the following items: study characteristics (author, publication year, study design), demographic data (tumor site, sample size), treatment characteristics (with or without 3D print template), and outcome data including D90(the dose of 90% of the target volume), D100, V90(the percent of the tumor target receiving 90% of the prescribed dose), V100, V150, V200, D2cc (the dose received by 2 cm 3 of normal tissue) and operation time.

Quality assessment
For RCTs, the methodological quality were assessed by Cochrane risk of bias tool. Non-RCTs were assessed by the Newcastle-Ottawa Scale (NOS) [10]. Two researchers (E.C. and J.W.) carried out the scoring independently, and debated until a full agreement was reached. Studies with a score more than 7 were considered high quality, 4-6 moderate and below than 4 low quality.

Statistical analysis
Standard mean difference (SMD) was adopted as the effect indicator for dosimetry and operation time.
Pooled SMD and 95% confidence interval (CI) were calculated. We used I 2 statistics to evaluate statistical heterogeneity. An I 2 value of 0-40% indicates low heterogeneity; 30-60%, moderate heterogeneity; 50-90%, substantial heterogeneity; 75-100%, considerable heterogeneity. The Mantel-Haenszel fixed effect model [11] was applied for p > 0.1, I 2 < 50%; data were pooled with the random-effects model when the I 2 > 50%. p < 0.05 was considered to indicate that the difference was statistically significant. Publication bias was assessed with Egger's regression. The statistical analysis were carried out using Stata 12.0 software.
Five studies [20][21][22][23][24]  . In three studies [25][26][27], both 3DPNCT and 3DPCT plans were designed Table 2 Quality assessment of included studies a A truly representative, B somewhat representative, C selected group, D no description of the derivation of the cohort b A drawn from the same community as the exposed, B drawn from a different source, C no description of the derivation of the non-exposed c A secure record, B structured interview, C written self-report, D no description d Demonstration that the outcome of interest was not present at start of study: A yes, B no e A study controls for demographics/comorbidities, B study controls for any additional factor (e.g., age, severity of illness), C not done f A independent or blind assessment, B record linkage, C self-report, D no description g Long enough for outcomes to occur? A yes, B no h A complete follow-up, B subjects lost to follow-up was unlikely to introduce bias, C follow-up rate 90% or lower, D no statement

First author and year
Representativeness a Selection of non-exposed b  Fig. 2 Forest plot of studies comparing post-implantation D90 and D100 between 3D print template and traditional free-hand implantation

Operation time
Three studies reported operation time. The heterogeneity result showed no significant heterogeneity (I 2 = 35.4%, p = 0.213). The fixed effect model was utilized. The result showed that 3D print template assisted RIS implantation could reduce operation time with statistically significant compared to taditional free-hand implantation (SMD = − 0.93; 95%CI = − 1.3 to − 0.51; p < 0.001) (as shown in Additional file 1: Fig. 1).

Publication bias
For studies comparing 3D print template-assisted implantation with traditional free-hand implantation, publication bias was evaluated by a funnel plot. The regression test of the funnel plot symmetry confirmed that no publication bias was found (p = 0.999, 0.373, 0.903, 0.833, and 0.964, respectively) for D90, D100, V90, V100, and operation time (as shown in Additional file 2: Fig. 2, Additional file 3: Fig. 3).

Discussion
RIS implantation has the dosimetric advantage of sharp dose gradients between tumor target area and adjacent normal tissues, which allows more sparing of the surrounding organs at risk. It has been widely used in China for the following tumors: head and neck, thorax, breast, abdomen, and pelvic cavity; and it has a good effect on relieving pain, reducing tumor burden, improving life quality and prolonging survival time of patients [28][29][30][31][32]. But except for prostate cancer, there is still no Fig. 4 Forest plot of studies comparing D90, D100, V90, and V100 between pre-and post-implantation with traditional free-hand implantation standard method to treat other tumors. In the past, 125 I seeds were implanted just by doctors' experience. However, it is challenging for doctors to insert many needles at 1 time into the targer in line with the preplan, which leads to a large difference in location of seeds and dose distribution between pre-and post-plan, finally leading to tumor local recurrence and complications [12][13][14][15][16][17][18][19]. Also, traditional free-hand 125 I seed implantation is very complicated and time consuming; the operators usually spend a lot of time learning these special skills [16,17]. Therefore, how to achieve a precise distribution of RIS in the tumor target area and to ensure that RIS implantation treatment is strictly followed up as preplanning are the research focuses. 3D print template is a personalized template which contains preset implant channel information and body surface information of patients' treatment area. Through accurate intraoperative reset of template and real-time planning of TPS, the consistency between actual implant channel and planned needle channel can be improved. With the assistence of a 3D print template, it is easy and efficient to insert needles at any arbitrary angle into the tumor target, meanwhile accurately reproducing the needle positions according to the preplan. This method has been shown to improve the accuracy of seed location and Forest plot of studies comparing D90, D100, V100, V150, and V200 between pre-and post-implantation with 3D print template dose distribution in many studies [9][10][11][12][13], but as far as we know, there is still a lack of evidence-based medical data regarding its effectiveness.
Our meta-analysis result firstly showed that there was no significant difference between pre-and post-implantation for all the parameters including D90, D100, V100, V150, V200 and D2cc of OARs with 3D print template and that the D90, D100, V90 and V100 in the template group were higher than those in the freehand group, indicating that 3D print template could provide good accuracy for RIS implantation. And through the template guidance, the operation time was also reduced. Liang et al. [7] treated 15 patients with cervical lymph node metastasis by 3D print template assisted RIS implantation, and found that the dose distribution in preplan can be achieved easily and satisfactorily by 3D print template. Zhang et al. [8] used 3D print template to assist RIS implantation in 14 patients, and the differences of D90, V90, V100 and V150 values pre-and post-implantation showed no statistically significant. Zhang et al. [12] analyzed the clinical data of 27 patients with RIS implantation (13 patients with template, 14 with freehand); the result showed that V90 (92.76% ± 1.89%) in the template group was significantly higher than that in the freehand group (84.59% ± 7.56%), the difference was statistically significant (p = 0.001). Huang et al. [33] treated 25 patients with head and neck tumors by RIS implantation with the guidance of 3D print template. According to the insertion site of the needle, the patients were divided into four groups: parotid gland and masseter area group (9 cases); maxillary and paranasal area group (8 cases); submandibular and upper neck area group (5 cases); posterior area group (6 cases). All the needles were inserted at their predetermined positions once. The average insertion time was 7.5 s for each needle, and no complications were observed. These studies all have indicated that 3D print template could not only improve postoperative dose distribution but also lower the difficulty of puncture and reduce the operation time.
In this meta-analysis, we also found that both 3DPNCT and 3DPCT plans could achieve prescription dose. Pooled analysis of D90, D100, V100, and D2cc of OAR showed no significant differences between 3DPNCT and 3DPCT groups. But compared with 3DPCT, in 3DPNCT group, both V150 and V200 were increased, indicating that 3DPNCT could increase the volume of high dose within tumor target. And the larger volume of high dose might produce more beneficial effects on local control. On the other hand, the number of through bone needles was reduced in 3DPNCT group, which showed Fig. 6 Forest plot of studies comparing D2cc of OARs between pre-and post-implantation with 3D print template that 3DPNCT was more safer in the respect of puncture route. However, there are several challenges in the broader use of 3D print template, which include good preoperative implantation designing, accurate 3D print template calibration, and the confidence of doctors in carrying out the procedures. The template is advantageous in challenging clinical cases, which include tumors close to important organs and tissues, blocked by the bones, or next to the important blood vessels. On the other hand, it is time-consuming to design and prepare 3D print template, though the needle could be inserted into the target more accurately and efficiently, leading to better dose consistency.
In this study, the advantages of 3D print template in RIS implantation were revealed by evidence-based medicine study for the first time. Our meta-analysis result showed that both 3DPNCT and 3DPCT assisted RIS implantation can realize the accurate distribution of RIS, and make the post implantation dosimetry more predictable, which provided evidences for clinical practice. However, there are shortcomings in our study: as the relevant studies included were all from China, it may lead to the selection bias of the literature. Also, we used SMD as the effect indicator for dosimetry and operation time to perform meta-analysis due to the differences in preplan among studies. The advantage of 3D print template in clinical efficacy such as local tumor control and longterm survival of patients still needs a larger sample and high-quality randomized controlled trial to verify in the future.